Plumbing for Beginners: What You Need for Bathtub Installation
Plumbing for Beginners: What You Need for Bathtub Installation
Blog Article
Listed here in the next paragraph you will discover a lot of great tips about How to Install a Bathtub.
Mounting a bath tub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately difficult task. If the old bathtub is readily accessible, the job can move quickly; if you need to open up a wall to remove the old bathtub as well as position the new bath tub, the task is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the brand-new one. Make certain you have certified yourself for the task and are comfortable attempting it. Rather than employing a contractor to take control of a halfway-completed task, it is far better to consider employing one prior to you begin. Chances are you might require an expert plumber to make tube links.
This post will certainly help you set up a new tub in your shower room if you have actually already purchased a brand-new tub and also do not require to alter the plan of your previous water pipes.
Your devices and product checklist should comprise the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, switch on the faucets to drain any type of water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome due to the limited access that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a cloth all set for the continuing to be water that will originate from the pipes. When the supply pipes have been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old sealing substance.
Prior to moving on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washing machines are in location in between the faucet and the sink. Secure the faucet in place with the manufacturer offered backnut. As soon as the faucet is firmly in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal faucet connectors. The former type should be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Mounting the Bath tub
Utilizing the two wood boards under its feet, position the tub in the called for position. The wooden boards are handy in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little points.
The next goal is to make sure that the tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the spirit level reviews degree.
To set up taps, fit the bottom of the furthest versatile tap port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water as well as inspect all joints and also brand-new pipework for leakages and also tighten them if required. Fill up the bath tub as well as also examine the overflow electrical outlet and the regular outlet for leakages.
Lastly, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and also sealing around the tub should wait till the bath tub has actually been used at the very least once as this will settle it right into its last position.
Planning for the Installment
First of all, the supporting structure supplied with the bathroom needs to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last position.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, creating the water to pass through the wall between the bathroom and also the tiling, bring about complications with dampness and feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes and cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealant can fracture relatively very early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently readily available on the marketplace. It is suggested to fit the ceramic tiles utilizing water-resistant or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on Tools You Need to Install a New Bathtub ? Try to leave a review down the page. We'd be glad to know your insights about this content. We are looking forward that you visit us again in the near future. Enjoyed our write up? Please share it. Let another person find it. We thank you for reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Details Report this page